Skeleton-Based Volumetric Parameterizations for Lattice Structures

2023-03-12 09:01LongChenShuxunLiangNanYanXiangqianYangandBaotongLi

Long Chen,Shuxun Liang,Nan Yan,Xiangqian Yang and Baotong Li

1School of Mechanical Engineering,University of Shanghai for Science and Technology,Shanghai,200093,China

2School of Optical-Electrical and Computer Engineering,University of Shanghai for Science and Technology,Shanghai,200093,China

3Key Laboratory of Education Ministry for Modern Design&Rotor-Bearing System,Xi’an Jiaotong University,Xi’an,710049,China

ABSTRACT Lattice structures with excellent physical properties have attracted great research interest.In this paper, a novel volume parametric modeling method based on the skeleton model is proposed for the construction of threedimensional lattice structures.The skeleton model is divided into three types of nodes.And the corresponding algorithms are utilized to construct diverse types of volume parametric nodes.The unit-cell is assembled with distinct nodes according to the geometric features.The final lattice structure is created by the periodic arrangement of unit-cells.Several different types of volume parametric lattice structures are constructed to prove the stability and applicability of the proposed method.The quality is assessed in terms of the value of the Jacobian matrix.Moreover,the volume parametric lattice structures are tested with the isogeometric analysis to verify the feasibility of integration of modeling and simulation.

KEYWORDS Lattice structure;volumetric parameterization;skeleton model;node modeling

1 Introduction

In recent years, the extensive application of additive manufacturing (AM) has rendered possibilities for fabricating complex components, such as lattice structures [1].The lattice structures exhibit low density,enhanced energy absorption,and excellent mechanical properties[2–4].It is widely used in the aerospace, petrochemical, and manufacturing industries as well as other fields [5].Most researches on lattice structures focus on the boundary representation(B-rep)models,which require to be transformed into a triangular or quadrangular mesh before simulation[6,7].However,generating the mesh takes 80% of the time in the entire design and analysis process [8], resulting in a serious reduction in productivity.Therefore,a unified geometric description of modeling and simulation has great advantages.The novel method of isogeometric analysis(IGA)[9]utilizes the same spline basis functions for geometric modeling and physical simulation making it possible to achieve the goal.Many studies have shown that the IGA has higher accuracy and robustness than the finite element analysis(FEA)[10].It is of great significance to construct a model suitable for IGA.

In this paper,a volume parametric modeling method of three-dimensional(3D)lattice structures is proposed based on the skeleton.The models constructed by our method are suitable for IGA without any transformation.In the entire modeling process,the construction of the volume parametric nodes is the key step.The unit-cell is assembled with different nodes by permutation and combination.And the lattice structure is created via the periodic arrangement of unit-cells.In addition,the toric surface is used as the transition surface to make the shape of the node smooth,which is beneficial to reduce stress concentration in the analysis.The main contributions are as follows:

1.A volume parametric modeling method of complex nodes is achieved.

2.Different types of volume parametric unit-cells and lattice structures are created.

3.The framework of integration of modeling and simulation is completed.

The remainder of the paper is organized as follows:In Section 2,some backgrounds and related works are introduced.The basic theory and algorithms are explained in Section 3.The modeling method of nodes is described in Section 4.The construction processes of unit-cells and lattice structures are presented in Section 5.Several models are provided to verify the effectiveness and the feasibility of the proposed method in Section 6.Finally,the conclusions are summarized in Section 7.

2 Related Works

The lattice structures with excellent properties have been widely applied in many industries.Researchers have proposed numerous modeling methods to construct lattice structures.Fan et al.[11]designed a honeycomb lattice structure and a sandwich structure with better mechanical properties than the solid structure, but the model is only two-dimensional.Masalha et al.[12] studied several algorithms to construct heterogeneous or trivariate fillets that support smooth filleting operation.The results verify the feasibility of the algorithms.Li et al.[13] proposed an improved algorithm based on the quartet structure generation set method.The algorithm reconstructed the 3D random porous structure.Leblanc et al.[14]introduced a modeling method based on the block to construct the complex model.The quality of the model heavily relies on the subdivision.Tang et al.[15]presented a novel design method for the periodic lattice structure.The frame generation algorithm is used to generate lattice wireframes based on the kernel.Tang et al.[16] studied an innovative hybrid geometric modeling method of lattice structures with three-stage, which involves generating lattice frames,constructing geometric functions,and voxelization.Liu et al.[17]proposed a memoryefficient modeling method and an adaptive slice algorithm of lattice structure to assist manufacturing.Lattice has an excellent performance in macrostructure as well as in microstructure simulation,such as multiscale crystal defect dynamics[18–22].It offers a possible solution to study crystalline plasticity on the nanoscale and mesoscale.

Manufacturing lattice structures is not easy via traditional processing technology due to the complex structure.The development of AM solves this problem.Dong et al.[23] summarized the existing modeling approaches and the characteristics of different AM in manufacturing cellular materials.Medeiros et al.[24]proposed an automatic adaptive voids algorithm with AM constraints to fabricate cellular structures with minimal material and maximum strength.Tang et al.[25]presented a method to connect the design and manufacturing process to improve the stiffness of heterogeneous lattice structures with manufacturing constraints.Garner et al.[26] utilized the optimization of individual cells and neighboring pairs to find the best connectivity and smoothness of the physical properties among the microstructures.Conde-Rodríguez et al.[27] proposed a modeling framework of heterogeneous structures based on Bezier patches.The method is appropriate to fabricate structures with different materials,but only single-level details and Bezier were permitted.

Compared with the B-rep models mentioned above,the volume parametric models utilize highorder non-uniform rational B-spline(NURBS)to express the physical domains precisely[28]and are suitable for IGA without any transformation.Meanwhile,the shape of the model remains unchanged after the refinement.On account of those characteristics,the volume parametric model has attracted a lot of attention.To make use of IGA more convenient, an interactive parametric design-analysis platform is designed [29].In the meantime, many parametric design methods have been proposed[30–33],which greatly extend the geometric modeling method.Moreover,Xiao et al.[34]utilized the surface interrogation technique for IGA and applied it to large-scale lattice-skin structures of several thousand intersections.Li et al.[35] investigated the behavior of functionally graded porous plates reinforced by graphene platelets,and incorporated within the IGA framework.Furthermore,different spline basis functions such as T-spline and PHT are utilized to construct the volume parametric model[36,37].These methods simplify the parameterization process and extend the application of IGA.

In this paper, a volume parametric modeling method of lattice structures based on the skeleton model is proposed.The method solves the problem of hexahedron segmentation of the complex nodes.And the modeling process is simplified by utilizing volume parametric nodes to assemble lattice structures.In addition,the toric surface is used as the transition surface to make the shape of the node smooth.Most importantly,the model constructed by the proposed method is suitable for isogeometric analysis.The proposed method realizes the integration of modeling and simulation.

3 Basic Theories and Overview of the Algorithm

3.1 Representation of the Volumetric Parameterization Model

The physical domain is defined based on the NURBS[38]and represented byΩinR3,as shown in Eq.(1).

The volume parametric model and NURBS basis function are described in Eqs.(2)and(3).

where,v,w)is the basic function of NURBS,Pi,j,k(i∈ [0,l],j∈ [0,m],k∈ [0,n])is the control point.Ni,p(u),Nj,q(v)andNk,r(w)are basis functions of B-spline defined in the three directionsU,V,W,respectively.p,q,rare the degrees,ωi,j,kis the weight factor ofPi,j,k.

3.2 Basic Definitions

The skeleton is an abstract description of the geometric model.It is widely used in segmentation,reconstruction,and geometric design.Many extraction algorithms are used to construct the skeleton model[39–42].The interactive design is the most commonly used method of skeleton construction[43].For periodic lattice structures,the unit-cell can be utilized to represent the topological information.In this paper,we build the skeleton model of unit-cells according to the different types of lattice structures and given by interconnected NURBS curves.The relationship of the skeleton is expressed by Eq.(4).Two typical lattice structure skeleton models are shown in Fig.1.

Figure 1:Typical skeleton models of the lattice structure.(a)Honeycomb lattice structure;(b)3D cubic lattice structure

The unit-cell is the basic element to generate a uniform lattice structure.Several representative unit-cells presented by the skeleton models are shown in Fig.2.

Figure 2:Typical unit-cell models obtained using the skeleton model

In this paper,we defined three types of nodes according to the number of branches.One branch indicates the end nodesEn,two branches indicate the joint nodesJn,and others are classified as the branch nodesBn,as shown in Fig.3.

Figure 3:Node models obtained with the skeleton curves.(a)En node;(b)Jn node;(c)Bn node

The connection part between nodes is composed of solid cylinders.It is divided into five primitive volumes to satisfy the parameterization requirement, as shown in Fig.4a.The cross-section of the cylinder is composed of B-spline surfacesSi(i=0,1,2,3,4)with the center pointoand radiusr.The width of the square isa=r/4.These five surfaces are used to construct the volume parametric modelsVi(i=0,1,2,3,4)by sweeping along the skeleton curve,as shown in Fig.4b.

Figure 4:The five primitive volumes.(a)Cross-section;(b)volume parametric modeling

3.3 Overview of the Algorithm

The input parameters to the algorithm include the skeleton modelScand the radiusrof the cross-section.The volume parametric lattice structureVsis the final output.The modeling process is illustrated in Fig.5.With the designed skeleton model,the nodes are divided into three types namelyBn,Jn,andEn.The unit-cell models are assembled with the different nodes according to the geometry and topology information.The volume parametric lattice structure is generated through the periodic arrangement of the unit-cells.

Figure 5:Algorithmic flow of the volume parametric lattice structure modeling

4 Modeling of the Nodes

4.1 Inner Hexahedral Group Construction of the Branch Node

Based on the research of the previous work [31], this study implements a “skeleton-aware”hexahedra group generation method.Firstly,an initial hexahedral boxVb0of trivariate B-spline volume parallel to the cartesian coordinate axis is generated at the center point of the node.Depending on the tangent direction of the branch curves,Vb0executes a“posture redirection”operation to make sure the branch curves penetrate from different surfaces.If each surface ofVb0intersects with only one branch,there is no need to conduct the“volume subdivision”operation.Otherwise,the volume subdivision ofVb0is executed to generate the final hexahedral boxVbox.Each surface ofVboxcan be used to construct a parametric patch along the direction of branch curves.The final hexahedral box of the branch node is shown in Eq.(5),whereNis the number of hexahedra.

The posture redirection operation ensures the branch curves penetrate from different surfaces ofVbox.The above constraint can be converted into the optimization equation shown in Eq.(6).Whered1,.....,dkis the direction of the branch curves.The functionf (UVW)takes the minimum value.εis an empirical parameter and greater than zero.

This is a nonlinear optimization problem.The length of the orthogonal basisUVWis the constraint.A principal component analysis method is used ford1,...,dkto set the initialUVW.The initial value ofεis 0.2 and decreases by a factor of 0.5 in each iteration.The posture ofVb0is confirmed after five iterations.

Vb0is updated after the posture redirection operation.As shown in Fig.6a,the initial hexahedron

Vb0has the three branch curvesd1,d2,d3penetrate from the same surfaceS0.If the posture redirection operation is not executed,S0must be divided into three subrectangular surfaces to satisfy the condition that each surface has only one intersection point with the branch curves at most.The three branch curves penetrate from the different surfacesS0,S1,S2after the operation of posture redirection.Thus, the volume subdivision operation is not needed.The final purpose of posture redirection is to ensure each subsurface intersects with only one branch curve.

Figure 6:Inner hexahedron group generation.(a)Posture redirection operation;(b)volume subdivision operation;(c)branch generation

After the posture redirection operation, there may still exist more one branch curves intersect with the same surfacef,as shown in Fig.6b.Therefore,the volume subdivision operation is required to generate aVb0composed ofVb1,Vb2,Vb3.

Each surface ofVboxgenerates a volume parametric patchVdi(i=0,...,k)and combines it into the inner hexahedron groupVinners,as expressed by Eq.(7).The branch curves andVboxare shown in Fig.6c.After two steps operations,Vinnersis composed ofVbox,Vd1,Vd2,Vd3,Vd4.

4.2 Outer Hexahedral Group Construction of the Branch Node

The outer hexahedrons of the node are constructed based on the inner hexahedron group modeling after the above steps.Firstly,construct the transition surfaces of the node.Then,the inner hexahedron group converts into multiple B-spline surfaces.Finally, the volume interpolation is used to generate the outer hexahedron group.

A toric surface is adopted here to create a closed surface of the node mostly because of the advantages of good smoothness[44,45].The construction algorithm is based on the multilateral Coons interpolation algorithm.Takingn(n≥3)curves as input parameters to build a toric surface.The definition of the bilinear Coons interpolation is given in Eq.(8).

Here,S1(u,v)is theU-direction ruled surface,S2(u,v)is theV-direction ruled surface,andT(u,v)is the linear mixed surface.The definition ofT(u,v)is provided in Eq.(9).

It is necessary to segment the outer surface to construct a closed transition surface.The intersection points of the sampling vectoron the boundary surfaceSendare calculated alongside the crosssection.The outer surface is divided into different shapes according to the number of intersections.The transition surface can be classified into four types,as shown in Fig.7.These shapes consist of 3,4,5,and 6 points.

Figure 7:Toric surface

Supposing there aren+1 volumes namedVi(i=0,1,.....,n),we define a set of boundary surface groupsSnocoms,as expressed in Eq.(10).

When the boundary surface inSnocomscontains the end pointpend,we name it the end surfaceSend.Each boundary surfaceSncis mapped and divided into B-spline surfaces on the transition surface except forSend[46].The sampling vectorvci(i=0,1,2,3)is defined on the cornerci(i=0,1,2,3)of eachSnc.Multiple sampling points and vectors can be calculated on the edges.As shown in Fig.8a,c0,c1,c2,c3are the corner points of the boundary surface,andare the sampling vectors of the corner pointsc0,c1,respectively.are the sampling vectors calculated alongc0,c1.

Figure 8:Calculate sampling vectors and corner vectors.(a)Sampling vectors of the boundary surface;(b)calculate corner sampling vector

The vector of each cornerciis calculated according to Eq.(11).

According to the mapping betweenSncandS(u,v), the volume interpolation algorithm [47] is used to construct the outer hexahedron groupVouters.The volume parametric nodeVBnis expressed by Eq.(13).

Figure 9: Outer hexahedron group modeling.(a) Boundary surface and transition surface mapping;(b)outer hexahedron group

The local patches of the outer hexahedron group and the final volume parametric node are shown in Fig.9b.

4.3 Modeling of Joint Nodes and End Nodes

After completing the modeling of the branch node, the cross-section is obtained, as shown in Fig.4a.Each cross-section is expressed by Eq.(14).

The end nodeEnis constructed with the cross-section groupSEn=(S0,S1,S2,S3,S4)and the skeleton curveCEn,as expressed in Eq.(15).

The stretch volumes are constructed through affine transformations of the section group along the skeleton curve as shown in Fig.10a.

Figure 10:Node modeling.(a)Extruding;(b)sweeping;(c)lofting

In addition, sweeping is another method to construct nodes.BothSEn(u,v),C(ωk)and the number of section groupskare needed.The number of knotsNω=r+k+2.ris the degree of the parameterω.The value ofωkdepends on the knot vectorW.The Frenet frame of the cross-section is constructed according to the knot,as shown in Eq.(16).The matrix of the control vertices is obtained by Eq.(17).

The other control pointsQi,j,kare calculated with the projection of the section groupSEn(u,v),as shown in Eq.(18).

Here,ωis the weight of the control pointPSi,j.M1is the transformation matrix between the local and the global coordinate system,M2is the Frenet transformation matrix.The construction of sweeping is shown in Fig.10b.

The joint node is constructed with the two section groupsSJn1=(S0,S1,S2,S3,S4)andSJn2=(S0,S1,S2,S3,S4)along the skeleton curveCJn(ω).Multiple section groups are calculated by interpolation,which is similar to the sweeping method.The joint node is shown in Fig.10c.

5 Modeling of the Unit Cell and the Lattice Structure

5.1 Modeling of the Unit Cell

The unit-cell of the lattice structure describes the local characteristics.The geometric parameters that control the specific shape of the unit-cell mainly include the size(i.e.,length,width,and height),section radius,and horizontal angles.According to the geometry and topology of the skeleton model,a volume parametric unit-cell is constructed through translation,rotation,and reflection of the nodes.The relationship between the unit-cellVuc(u,v,w)and the skeleton modelCuc(u)is expressed by Eq.(19).

For example, the skeleton of the simple cubic unit-cell shown in Fig.11c is split into two basic nodes,as shown in Figs.11a and 11b.The volume parametric models of the two nodes are constructed as illustrated in Figs.11d and 11e.The final unit-cell model is obtained through translation,rotation,and splicing operations,as shown in Fig.12f.

Figure 11:Simple cubic unit-cell model generation.(a)Node skeleton;(b)node skeleton;(c)unit-cell skeleton;(d)node model;(e)node model;(f)unit-cell model

Figure 12:Simple cubic lattice structure model generation.(a)Unit-cell model;(b)joint node model;(c)lattice structure model

5.2 Modeling of the Lattice Structure

The unit-cell of the uniform lattice structure is a parallelepiped.Three translation basis vectors intersect at the vertex.The skeleton with three orthogonal translation basis vectors is called the cubic lattice structure.Due to the unique symmetry properties,the cubic lattice structure is the most widely used type.The modeling process mainly includes two steps.Firstly,the unit-cell is constructed as the basic element.Secondly, duplicate the unit-cells in space to form the lattice structure.The center of the unit-cell is used to indicate the location.Finally,unit-cells are arranged along the translation basis vectors to generate the volume parametric lattice structures.

A simple cubic lattice structure that satisfies geometric connectivity is shown in Fig.12.The volume parametric unit-cell is composed of 308 trivariate NURBS volumes as shown in Fig.12a.We set the translation basis vectors as the coordinate axis directions,and a series of operations involving the translation basis vector directions are executed.The connectivity among unit-cells is guaranteed by the joint node as shown in Fig.12b.The volume parametric lattice structure with 4096 trivariate NURBS volumes is constructed as shown in Fig.12c.

6 Examples and Simulation

We constructed several models of node and lattice structure to prove the effectiveness and applicability of the proposed method.In the meantime, the Jacobian values of the models are calculated and visualized to evaluate the quality.And the IGA is utilized to verify the feasibility of integration of modeling and simulation of our method.

Figure 13:Modeling process of orthogonal branch nodes.(a)Hexahedron box;(b)inner hexahedron groups;(c)transition surfaces;(d)volumetric parameterization nodes

6.1 Examples of Branch Node Models

Several nodes are constructed with the modeling method presented in Section 4.The nodes with orthogonal branches are shown in Fig.13, and the others are shown in Fig.14.The branch curves with the hexahedron boxes are shown in column(a),the inner hexahedron groups are shown in column(b),the transition surface models constructed with multiple toric surfaces are shown in column(c),and the volume parametric nodes are shown in column(d).The parameters of nodes are listed in Table 1.The first four cases are classified as orthogonal nodes, the length of the branch curves is 2, and the diameter of the cross-section is 2.The last five cases are classified as complex nodes with a length of 3 and the same diameter.

Figure 14: Modeling process of complex branch nodes.(a) Hexahedron box; (b) inner hexahedron groups;(c)transition surfaces;(d)volumetric parameterization nodes

Table 1: Parameters of the branch nodes

6.2 Examples of Unit-Cell Models

According to Section 5, we construct some typical unit-cell models as shown in Fig.15.The parameters are listed in Table 2.The diameter of the cross-section of joint nodes is 2.

Figure 15: The unit-cell models.(a) Simple cubic unit-cell(Cell-1); (b) body-centered cubic unitcell(Cell-2); (c) face-body-centered cubic unit-cell(Cell-3); (d) 3D-Kagome unit-cell(Cell-4); (e) 3Dpyramidal unit-cell(Cell-5);(f)body-centered-plus unit-cell(Cell-6)

Table 2: Parameters of the unit cell

Table 2 (continued)Name Node number Node type Volume patches Control vertice number Joint node length Cell-4 71 Bn,Jn 61 1647 8 Cell-5 9 Bn,Jn 84 2268 8 Cell-6 11 Bn,Jn 102 1647 8

6.3 Examples of Lattice Structures

Based on the abovementioned unit-cells,several different types of volume parametric lattice structures are constructed as shown in Fig.16.Some sandwich-type of lattice structures are also built as shown in Fig.17.The 3D view of the models is presented in the first column,and the front view is illustrated in the second column.The parameters of the lattice structures are listed in Table 3.

Figure 16:Multiple cubic lattice structure models

Figure 17:Sandwich-type lattice structure models

Table 3: Parameters of the lattice structures

6.4 Evaluation of the Model Quality

To verify the volume parametric model is suitable for IGA without intersections, overlaps, or large-angle distortions of hexahedrons,the value of the Jacobian matrix is the main index for quality assessment[48–50].In addition,the Jacobian value should be greater than zero and the distribution should be as evenly as possible within the parameter domain.The calculation of the Jacobian value is provided with the expression Eq.(20).

The Jacobian values of the nodes and the unit cells are shown in Figs.18–20.The Jacobian values are bigger than zero,and the distribution is relatively symmetrical.The quality evaluation of volume parametric lattice structures is shown in Fig.21.The Jacobian values demonstrate excellent quality and satisfy the requirement of analysis.Therefore,the quality of the models obtained by the proposed method is verified.

Figure 18:Jacobian values of orthogonal branch nodes

Figure 19:Jacobian values of complex branch nodes

Figure 20:Jacobian values of unit-cell models

Figure 21:Jacobian values of the lattice structure models

There are some singularities in the models constructed by the proposed method, which are reflected in the minimum values of the Jacobian.Singularities damage the quality of the model.How to control the singularity is a major issue of geometric modeling.Researchers have proposed some approaches, such as utilizing sparse distributed directional constraints to determine the appropriate singularities[51],designing different templates to handle the features of new singularities[46],or using a practical framework to adjust singularity graphs by modifying the rotational transition[52].Some researchers use novel tetrahedral split operations to preprocess singularity-restricted frame fields[53].These methods achieve the goal of controlling the singularity but bring a huge extra computation at the same time.The model of lattice structure is especially difficult to deal with singularities with complex nodes and massive volume parametric patches.Considering the Jacobian values still meet the requirement of IGA, the singularities are not specifically controlled in the modeling process of this paper.

6.5 Model Verification via IGA

We applicated IGA to the volume parametric models to verify the applicability.As shown in Figs.22 and 23, the boundary conditions are shown in column (a).We set the material as stainless steel,Young’s modulus is 2.0×1011Pa,Poisson’s ratio is 0.3,Bulk modulus is 1.6667×1011Pa,and Shear modulus is 7.6923×1010Pa.The results of IGA are shown in column(b).We added the FEA results of the same geometric model as a comparison in column(c).

Figure 22: (Continued)

Figure 22:Results of the IGA and FEA conducted on the unit-cell models

The boundary conditions are illustrated in Fig.22a.The load is equal to 440N,and the adaptive mesh numbers of the four cases are 36445, 7438, 5545, and 2672, respectively.The maximum displacements of the four models are 2.6×10-7,2.5×10-6,1.5×10-6,and 1.1×10-5mm.The results of FEA calculated by commercial software are similar,and the distribution of values is the same.The IGA is also applicated to a simple lattice structure as shown in Fig.23.We can see the results of the two methods exhibit the same distribution as shown in Figs.23b and 23c.

Figure 23:Results of the IGA and FEA conducted on the lattice structure model

With the above examples, we have proved the volume parametric models constructed by our method are suitable for IGA, and the feasibility of integration of modeling and simulation is verified too.

7 Conclusions

In this paper,a volume parametric modeling method of 3D lattice structures based on the skeleton model is proposed.The unit-cell is combined with different volume parametric nodes.And the volume parametric lattice structure is assembled with the periodic arrangements of the unit-cells.The effectiveness and stability of the proposed method are proved with numerous examples.The quality of the volume parametric models is evaluated by Jacobian values.And finally,the feasibility of integration of modeling and simulation is proved with isogeometric analysis.

However, the quality of complex nodes is still not perfect enough, and how to control the singularity is also an important issue.In addition, the manufacturing of volume parametric lattice structures is worth to be studied in the future,and applying these models to crystal dynamics is also significant.

Funding Statement:This research is supported by the National Nature Science Foundation of China under Grant No.52075340.

Conflicts of Interest:The authors declare that they have no conflicts of interest to report regarding the present study.